Using One-Push Configuration - AOSS or WPS
One-Push Configuration using AOSS or WPS allows you to configure a wireless network easier than configuring it manually. By pushing a button on the wireless router or access point, information is transmitted and automatically configured for wireless network devices. With WPS, you may also use a PIN for a more secure setup.
To use One-Push Configuration, your router or access point must also support AOSS or WPS. Consult the documentation of your router or access point to determine if it is supported and how to use it. Refer to the following link to obtain contact information for common router manufacturers:https://brothercanadaen.custhelp.com/euf/assets/images/answers/download/Wireless_Router_Information_EN.htm
NOTE: Using the One-Push Configuration setting of your router may reconfigure your network settings, such as SSID/Network name or security information.
- For AOSS or WPS Configuration
- For WPS w/ PIN Code Configuration
1. Power on the Brother machine and temporarily place it within the acceptable range of the access point or router to use this feature. Once the unit is configured, you may relocate the devices to any acceptable range for wireless communication.
2. Was the Brother machine previously configured for a wireless connection?
- Yes: Continue to STEP 3 below.
- No: Continue to STEP 4 below.
3. Reset the Network Card to configure new settings. This will erase all current network settings.
- Press MENU on the Brother machine.
- Press the DOWN ARROW key to select Network and then press OK.
- Press the DOWN ARROW key to select Network Reset and then press OK.
- Press the UP arrow key to choose Reset.
- Press the UP arrow key to choose Yes. The machine's network card will be reset.
4. Activate WPS/AOSS from the menu.
- Press MENU on the Brother machine.
- Press the DOWN ARROW Key to select Network and then press OK.
- Press the DOWN ARROW Key to select WLAN and then press OK.
- Press the DOWN ARROW Key to select WPS/AOSS and then press OK.
- If the LCD states: WLAN Enable?, press the UP ARROW key to select On.
5. When the LCD states: Start WPS/AOSS on your wireless access point/router., press the WPS/AOSS button on your router or access point.
NOTE: For instructions on how to access this feature, refer to the documentation for your access point or router.
Only one WPS/AOSS device can be configured at a time.
6. Press OK on the Brother machine. The machine will search for an access point and attempt to connect.
A Wireless LAN report will automatically print with the connection results.
- Once the connection has been successfully established between the Brother machine and the access point, Connected will be displayed on the LCD screen. Continue to the Software Installation section for information on how to install the software on your computer.
- If you receive Connection Error, No Access Point or Connection Failed, this indicates that the connection was not successful.
o A session overlap may have been detected. Make sure that there are no other devices broadcasting WPS or AOSS within the vicinity of the Brother machine. Press OK to clear the message.
o You may attempt the setup again.
o If you consistently receive an error, we recommend that you configure your Brother machine using an alternate method. For alternative methods, refer to: "How do I connect the Brother machine to a wireless network?"
WPS w/ PIN Code Configuration:
1. Power on the Brother machine and temporarily place it within the acceptable range of the access point or router to use this feature. Once the unit is configured, you may relocate the devices to any acceptable range for wireless communication.
2. Was the Brother machine previously configured for a wireless connection?
- Yes: Continue to STEP 3 below.
- No: Continue to STEP 4 below.
3. Reset the Network Card to configure new settings. This will erase all current network settings.
- Press MENU on the Brother machine.
- Press the DOWN ARROW key to select Network and then press OK.
- Press the DOWN ARROW key to select Network Reset and then press OK.
- Press the UP arrow key to choose Reset.
- Press the UP arrow key to choose Yes. The machine's network card will be reset.
4. Activate WPS w/ PIN Code from the menu:
- Press MENU on the Brother machine.
- Press the DOWN ARROW Key to select Network and then press OK.
- Press the DOWN ARROW Key to select WLAN and then press OK.
- Press the DOWN ARROW Key to select WPS w/PIN Code and then press OK.
- If the LCD states: WLAN Enable?, press the UP ARROW key to select On.
- The Brother machine's LCD will display an 8-digit pin.
5. Press the WPS button on your router or access point.
NOTE: For instructions on how to access this feature, refer to the documentation for your access point or router.
6. Enter the pin from the Brother machine into the WPS Pin section of your access point or router.
NOTE: Only one WPS device can be configured at a time.
7. The machine will search for a WPS access point and attempt to connect. A Wireless LAN report will automatically print with the connection results.
- Once the connection has been successfully established between the Brother machine and the access point, Connected will be displayed on the LCD screen. Continue to the Software Installation section for information on how to install the software on your computer.
- If you receive Connection Error, No Access Point or Connection Failed, this indicates that the connection was not successful.
o A session overlap may have been detected. Make sure that there are no other devices broadcasting WPS or AOSS within the vicinity of the Brother machine. Press OK to clear the message.
o You may attempt the setup again.
o If you consistently receive an error, we recommend that you configure your Brother machine using an alternate method. For alternative methods, refer to: "How do I connect the Brother machine to a wireless network?"
Uninstall previously installed software
If you have previously installed the software and you need to uninstall it after changing your network configuration, refer to the following solutions for uninstall instructions.
NOTE: Click here for information on how to install or reinstall the software.
Windows Users:
- "How do I uninstall the Brother MFL-Pro Suite software from my Windows computer?"
Macintosh Users:
- "How do I completely remove the Brother software and drivers from Macintosh OS X 10.7 or 10.8?"
- "How do I completely remove the Brother software and drivers from Macintosh OS X 10.9?"
Install or reinstall the software:
Visit http://www.brother.ca to download the latest drivers or software. You may also install the software from a CD that is compatible with your operating system, if available.
Windows Users:
- "How do I download and install the full driver and software package for Windows?"
Macintosh Users:
- "How do I download and install the full driver and software package for Macintosh?"
Mobile Device Users:
- Install the "Brother iPrint&Scan" App onto your mobile device.
